12
Dec
1. Ventilation
Ventilation is a machine that relies on the input mechanical energy to increase the gas pressure and discharge the gas. It is a driven fluid machine.
Fans are widely used in ventilation, dust removal, and cooling of factories, mines, tunnels, cooling towers, vehicles, ships, and buildings; ventilation and drafting of boilers and industrial furnaces;
Cooling and ventilation in air-conditioning equipment and household appliances; drying and sorting of grain; wind tunnel wind source and inflation and propulsion of hovercraft, etc.
The working principle of the ventilator is basically the same as that of the turbo compressor, but because the gas flow rate is low and the pressure changes little, it is generally not necessary to consider the change of the gas-specific volume, that is, the gas is treated as an incompressible fluid.
2. Blower
Under design conditions, a fan with a wind pressure of 15kPa~0.2MPa or a compression ratio e=1.15~3 is called a blower.
Features:
1. Since the impeller runs without friction in the body, no lubrication is required, so the discharged gas does not contain oil. It is an ideal pneumatic conveying gas source for chemical, food and other industries.
2. The blower is a volumetric operation type blower. When in use, with the change of pressure, the flow rate changes very little. But the flow rate changes with the speed. Therefore, the selection range of pressure services is very wide, and the selection of flow rate can meet the needs by selecting the speed.
3. The speed of the blower is high, and the gap between the rotor and the rotor, and between the rotor and the body is small, so there is less leakage and higher volumetric efficiency. Our factory has strong processing and assembly technology, which can ensure a reasonable and uniform gap, achieve high volumetric efficiency and avoid friction in the body due to thermal expansion.
4. The structure of the blower determines that its mechanical friction loss is very small. Because only the bearing and the gear pair have mechanical contact in the material selection, the rotor, casing, and gear ring have sufficient mechanical strength. Safe operation and long service life are major features of blower products.
read more
31
May
Introduction:
In the realm of comfort cooling, two commonly used systems are Variable Refrigerant Volume (VRV) and Air Handling Unit (AHU). While both serve the purpose of providing a comfortable indoor environment, there are significant differences between these systems in terms of their working principles,... read more
05
Jul
In the mining industry, mining ventilation fans play a critical role in providing safe ventilation and reducing mine temperatures. To ensure the normal operation and safe stability of your mining ventilation fans, comprehensive testing is essential. As a professional testing agency, we are committed... read more
25
Oct
Whenever the heating season arrives, most areas in the north will be accompanied by smog. Since the “13th Five-Year Plan”, the central and local governments have paid special attention to the control of environmental pollution, especially smog. The central government has demarcated the Beijing-Tianjin-Hebei air pollution transmission channel for it and directly subsidized the “2+26” cities from the central government to control smog pollution. So the north began the tide of coal-to-electricity and coal-to-clean energy.
Two or three years ago, most people didn’t know much about air-to-air heat pump products. If they were slightly impressed, they might be air-to-water heaters, but they didn’t know anything about other products. Such as air-energy floor heating and air-conditioning integrated machine, air-energy heat pump dryer, and so on. After the popularization of “coal-to-electricity” in the north, most people know what an air energy heat pump is. So what is the difference between the ultra-low temperature air energy heat pump used in the north and the ordinary air energy heat pump?
The operating conditions of the two are different.
We all know that the working principle of the air energy heat pump is to convert the heat in the air into the available high heat energy through the compressor, and then exchange it with the water system to provide hot water, heating, cooling, drying, and other purposes. The temperature environment in which the ordinary air source heat pump operates is preferably within minus 10 ℃. If it operates at minus 10 to 25 ℃, it may appear:
1. Compressor is prone to failure
The temperature of the exhaust gas rises rapidly, and the overheating of the working medium is too high. In the case of overheating of the working medium, the thermal conductivity of the working medium in the condenser decreases sharply, and at the same time, the temperature of the lubricating oil increases and the viscosity decreases, which affects the normal lubrication of the compressor.
2. The unit cannot defrost
In frequent rain and snow weather and low temperature, the defrosting ability of the unit is easily weakened. Because the air intake of the unit is too small, the density of the air that can be inhaled is reduced. With the accumulation of time, the thickness of the frost layer is getting higher and higher. Therefore, the unit will reduce the circulation of the refrigerant due to the decrease in the air conversion capacity, and the overall heating capacity will decrease.
The two technologies involved are different
Because of the difference in an ambient temperature between the north and the south, most air energy heat pump manufacturers are located in the southern Guangdong area. The air energy market in the south is extensive. The earliest product is also an air energy water heater. With the development of air energy, its technology is also becoming more and more mature. Heating has also gained a firm foothold in the north, which is also the fundamental reason for the breakthrough growth of coal-to-electricity air-energy heat pumps in the north in the past three years.
So what kind of technology does low-temperature air energy have to gain a firm foothold in the cold northern regions? There are three main points:
1. Ultra-low Temperature air Energy Operation Technology Air energy heat pump manufacturers have their own ultra-low temperature technology. Since the air energy heat pump host is generally installed outdoors, the phenomenon of frost will frequently occur in rainy and snowy weather. The ultra-low temperature air energy heat pump host can intelligently judge the defrosting needs, and intelligently judge whether to defrost according to the operating conditions of the unit (running time, exhaust temperature, etc.), combined with the ambient temperature and frost thickness. Defrost with frost and no defrost without frost, greatly extending the defrosting cycle, shortening the defrosting time by 20%, and ensuring the efficient operation of the unit.
2. Jet Enthalpy Technology
Because the heating efficiency of the air-energy heat pump in extremely cold weather will be greatly attenuated, resulting in an unsatisfactory heating effect. The ultra-low temperature air energy heat pump uses the jet enthalpy increase technology to create a second suction port on the scroll, and through the second suction circuit, the refrigerant flow is increased, and the circulation volume of the unit is increased during cooling. Compared with the general unit, the cooling capacity is increased by 10%, which greatly improves the refrigerant circulation system, makes full use of the refrigerant flow and utilization rate in the compressor, and improves the stability of the system operation and the heating efficiency.
3. Shell and Tube Heat Exchanger
Ordinary air can use a plate heat exchanger, which is easy to scale and block the flow passage. Low-temperature air can use copper tubes with internal thread and external fins. The water inside the tube and fluorine outside the tube. The heat exchange area is large and the heat exchange efficiency is high.
read more
15
Jan
Today is the weekly reading and sharing session.
Every employee will publish their reading experience.
The company also provides employees with leisure places after meals — Book Corner.
All kinds of books are available, providing convenience for employees.
The atmosphere of the company is harmonious, focusing on the... read more
12
Jul
Zibo Decent Machinery recently announced a partnership with a well-known pharmaceutical factory in Afghanistan to successfully carry out a chiller project. This collaboration is a continuation of the long-term relationship between both parties and also represents a significant breakthrough for Zibo Decent Machinery in... read more
05
Jun
At the end of June, samples of Roots blower will be sent to our Singapore warehouse for testing.
If you want to check the goods,please feel free to contact us.
Email:[email protected]
read more
28
Jun
When it comes to air conditioning solutions, Zibo Decent Machinery is at the forefront of innovation and efficiency. In June 2023, we received an inquiry from the prestigious Bolivian Government Hospital project. They had a unique requirement for a custom split direct expansion unit,... read more
20
Jan
2020.1.20,our company held a commendation conference in 2019 and outlook for 2020.
The first is the company’s development history, which was briefly introduced through two VCRs.(Facebook:scy ventilation)
Next is a recognition ceremony for employees,the picture below is the style of all employees.
The happiest part is the... read more